Racoon VPN-Verbindung mit Bintec VPN Access 25

Hallo, ich habe Suse 10.1 laufen und versuche mittels Racoon eine VPN-Verbindung zu einem Bintec Bintec VPN Access 25 herzustellen. Das scheint auch zu funktionieren, aber leider komme keine Pakete durch den Tunnel durch. Weder "Ping" noch "telnet" funktioniert.

Anbei meine Konfigs .. vllt. hat ja einer eine Idee die mir weiterhilft.


racoon.conf

[code]

path include "/etc/racoon";
path pre_shared_key "/etc/racoon/psk.txt";
path certificate "@sysconfdir_x@/cert";

1. "padding" defines some padding parameters. You should not touch these.

padding
{
maximum_length 20; # maximum padding length.
randomize off; # enable randomize length.
strict_check off; # enable strict check.
exclusive_tail off; # extract last one octet.
}

1. if no listen directive is specified, racoon will listen on all
2. available interface addresses.

listen
{

isakmp 192.168.1.22 [500];
isakmp 192.168.1.22 [4500];
#isakmp ::1 [7000];
#isakmp 202.249.11.124 [500];
#admin [7002]; # administrative port for racoonctl.
#strict_address; # requires that all addresses must be bound.
}

1. Specify various default timers.

timer
{
counter 5; # maximum trying count to send.
interval 20 sec; # maximum interval to resend.
persend 1; # the number of packets per send.

phase1 30 sec;
phase2 15 sec;
}

remote anonymous
{
exchange_mode aggressive;
verify_identifier on;
my_identifier user_fqdn "remote@bintec.de";
peers_identifier user_fqdn "zentrale@bintec.de";
doi ipsec_doi;
situation identity_only;

#certificate_type x509 "my.cert.pem" "my.key.pem";

nonce_size 16;
initial_contact on;
proposal_check obey; # obey, strict, or claim

proposal {
encryption_algorithm 3des;
hash_algorithm md5;
authentication_method pre_shared_key;
dh_group 2;
}
}


sainfo anonymous
{
pfs_group 2;
encryption_algorithm 3des;
authentication_algorithm hmac_md5;
compression_algorithm deflate;
}

sainfo subnet 192.168.1.0/24 any subnet 10.22.0.0/24 any
{
pfs_group 2;
encryption_algorithm 3des;
authentication_algorithm hmac_md5;
compression_algorithm deflate;
}


[/code]


setkey.conf

[code]

1. This is a sample setkey.conf

1. First of all flush the SPD database

spdflush;

1. Add some SPD rules
2. Very likely you'll want to replace these rules with your own ones

spdadd 127.0.0.0/8 127.0.0.0/8 any -P out none;
spdadd 127.0.0.0/8 127.0.0.0/8 any -P in none;

spdadd 192.168.1.0/24 10.22.0.0/24 any -P out ipsec
esp/tunnel/192.168.1.22-85.116.x.x/unique;

spdadd 10.22.0.0/24 192.168.1.0/24 any -P out ipsec
esp/tunnel/85.116.x.x-192.168.1.22/unique;
[/code]


Weiterhin habe ich in der racoon (unter init.d) einen Eintrag gemacht, welcher mir eine Route zum Zielnetz über Eth0 erstellt.

Jmd ne Idee wo der Fehler liegen könnte ?

Gruß aus Mainz,
Nico