laurel
Goto Top

Schwerer Ausnahmefehler

beim herunterfahren !

Hallo,
hab bei meinem alten PC jetzt dauernd beim herunterfahren Bluescreens:
Schwerer Ausnahmefehler 0D in an Adresse 0028:C00028C6 in der VXD Datei VMM(01)+000018C6 aufgetreten. Die aktuelle Anwendung wird beendet.
oder
Schwerer Ausnahmefehler 0D in Adresse 017F:BFF9DFD4 aufgetreten. Die aktuelle Anwendung wird beendet.
Ich kann dann nur noch den Ausschalter gedrückt halten bis es aus geht.
Beim neuen Hochfahren macht er dann scandisc und alles läuft wieder normal bis zum nächsten herunterfahren.
System:
Win98se / Award Bios / IP IIIe, 700MHz
MB: Biostar M6VBe / Chipsatz: Via vt82c693a Apollo pro 133
Graka: Ati Rage 128 expert 2000
2x 128er Ram-Riegel (gleiche)

Dieser alte Rechner wird nur für Bürokram benutzt, also wird eigentlich nie so richtig ausgelastet.
Er ist auch nicht am Internet angeschlossen, daher wurde auch nie irgendwas upgedatet.
Sind alles die Ur-Treiber drauf von Anno Dazumal.
Was ist die Ursache für die Bluescreens und was kann ich dagegen tun ?

M.f.G. Laurel

Content-Key: 43050

Url: https://administrator.de/contentid/43050

Printed on: April 26, 2024 at 13:04 o'clock

Member: Sella
Sella Jan 28, 2007 at 17:05:07 (UTC)
Goto Top
Das hab ich beim MS dazu gefunden

STOP: 0x0000000D (parameter, parameter, parameter, parameter) MUTEX_LEVEL_NUMBER_VIOLATION
Explanation:

This is a Windows 2000 Executive character-mode STOP message. It indicates an attempt to acquire a lower-level mutex.
User Action:

If this is the first time you have booted after installing new hardware, remove the hardware and boot again. Check the Microsoft Hardware Compatibility List to verify that the hardware and its drivers are compatible with Windows 2000. For information about the hardware, contact the supplier. If you are installing Windows 2000 for the first time, check the Windows 2000 system requirements, including the amount of RAM and disk space required to load the operating system. Also, check the Hardware Compatibility List to verify that the system can run Windows 2000. If Windows 2000 is loaded and no new hardware has been installed, reboot with recovery options set to create a dump file. If the message continues to appear, select the Last Known Good option when you reboot. If there is no Last Known Good configuration, try using the Emergency Repair Disk. If you do not have an Emergency Repair Disk, contact your technical support group.

http://msdn.microsoft.com/library/default.asp?url=/library/en-us/w2kmsg ...

Mehr kann ich dazu nicht sagen da mir 0D noch nie untergekommen ist


Karl
Member: cykes
cykes Jan 28, 2007 at 18:22:14 (UTC)
Goto Top
Hi,

@Sella bei Win98 gab es die STOP Fehlermeldungen in der Form noch nicht.

@Laurel Ist in jedem Fall ein Treiberfehler, ich würde eventuell mal nach aktuellen Treiber für die
im Rechner befindliche und extern angeschlossene Hardware suchen. Ist zufällig ein Umax Scanner an die Maschine angeschlossen? Ein paar weitere Tips finden sich u.a. hier
http://www.supportnet.de/discussion/listmessages.asp?autoid=3966

Gruß

cykes

[EDIT] Könnte eventuell auch eine (fast) volle C: Parttion sein.... Einfach mal Google
anschmeissen und nach "vxd vmm" suchen, da gibt's noch einige Tips...