serial90
Goto Top

Cisco 2951 - CME Installation

Moin Moin!

ich habe ein Problem mit meinem 2951 und CME bzw. telephony-service.

Wenn ich versuche den Befehl einzugeben passiert nichts, normalerweise müsste der Router dann ja aber in den telephony-service config mode gehen?!

CISCO2951(config)#telephony-service 
CISCO2951(config)#

Mache ich ein sh version sieht es so aus:

Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.4(3)M7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Thu 02-Feb-17 23:18 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)

CISCO2951 uptime is 13 minutes
System returned to ROM by reload at 20:14:00 CEST Thu Jul 20 2017
System restarted at 20:16:30 CEST Thu Jul 20 2017
System image file is "flash0:c2951-universalk9-mz.SPA.154-3.M7.bin"  
Last reload type: Normal Reload
Last reload reason: Reload Command



This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco CISCO2951/K9 (revision 1.1) with 485376K/38912K bytes of memory.
Processor board ID FCZ15047E0Y
3 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
DRAM configuration is 72 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
254464K bytes of ATA System CompactFlash 0 (Read/Write)
999936K bytes of ATA CompactFlash 1 (Read/Write)


License Info:

License UDI:
          
-------------------------------------------------
Device#   PID                   SN
-------------------------------------------------
*1        CISCO2951/K9          FCZ15047E0Y     



Technology Package License Information for Module:'c2951'   

------------------------------------------------------------------------
Technology    Technology-package                  Technology-package
              Current              Type           Next reboot  
------------------------------------------------------------------------
ipbase        ipbasek9             Permanent      ipbasek9
security      securityk9           Permanent      securityk9
uc            uck9                 Permanent      uck9
data          datak9               Permanent      datak9
NtwkEss       None                 None           None
CollabPro     None                 None           None

Configuration register is 0x2102


Und bei einem sh license so:


Index 1 Feature: ipbasek9                       
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Medium
Index 2 Feature: securityk9                     
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Medium
Index 3 Feature: uck9                           
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Medium
Index 4 Feature: datak9                         
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Medium
Index 5 Feature: NtwkEssSuitek9                 
        Period left: Not Activated
        Period Used: 0  minute  0  second  
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
        License Count: Non-Counted
        License Priority: None
Index 6 Feature: CollabProSuitek9               
        Period left: Not Activated
        Period Used: 0  minute  0  second  
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
        License Count: Non-Counted
        License Priority: None
Index 7 Feature: LI                             
Index 8 Feature: ios-ips-update                 
        Period left: Not Activated
        Period Used: 0  minute  0  second  
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
        License Count: Non-Counted
        License Priority: None
Index 9 Feature: SNASw                          
        Period left: Not Activated
        Period Used: 0  minute  0  second  
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
        License Count: Non-Counted
        License Priority: None
Index 10 Feature: hseck9                         
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Medium
Index 11 Feature: cme-srst                       
        Period left: Life time
        License Type: RightToUse
        License State: Active, Not in Use, EULA accepted
        License Count: 0/0  (In-use/Violation)
        License Priority: Low
Index 12 Feature: mgmt-plug-and-play             
Index 13 Feature: mgmt-lifecycle                 
Index 14 Feature: mgmt-assurance                 
Index 15 Feature: mgmt-onplus

Zu guter letzt noch die Ausgabe von sh telephony-service:

CISCO2951# sh telephony-service 
telephony-service is not enabled

Meine Frage nun: Wie aktiviere ich den telephony service? Damit ich dann die Telefone einrichten kann am Router.

Ich habe mich nun schon durch unzählige Cisco Tutorials gelesen aber alles endet damit das er den Befehl nicht annimmt?!

Die Befehle für voice-service-voip gehen alle Problemlos und ich habe auch schon Dialpeers und einen angemeldeten SIP-Trunk, nur ohne Telefone bzw CME alles wertlos.

Vllt. hat hier ja jemand noch eine Idee oder sieht meinen Fehler.

Oder muss ich noch ein PVDM-Modul für 1500€ dazu nehmen? Dachte eben nicht, da es ja auch 880 er gibt die das von Haus aus können?!

Vielen Dank!

Content-ID: 344031

Url: https://administrator.de/forum/cisco-2951-cme-installation-344031.html

Ausgedruckt am: 23.12.2024 um 13:12 Uhr